2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2026
* DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
* The ignition timing is retarded to reduce the potential of engine damaging spark knock.
Conditions for Clearing the DTC
DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
Diagnostic Aids
* Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set.
* Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set.
* The KS mounting surface should be free of burrs, casting flash, and foreign material.
* The KS must be clear of hoses, brackets, and engine electrical wiring.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
J 35616 GM Approved Terminal Test Kit
Circuit/System Verification
1. Engine at operating temperature, observe DTC information with a scan tool. DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or
P0333 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
P0324
Note: If DTC P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are also set, diagnose those DTCs first.
DTC P0324 indicates an internal control module circuitry failure. Replace the ECM.
P0325, P0326, P0327, P0328, P0330, P0332, P0333
1. Ignition OFF, disconnect the affected KS.
2. Ignition OFF. Connect a DMM to both KS signal circuits, terminals A and B, at the affected KS. Set the DMM to the 400 mV AC scale,
select the Hz mode. Let the reading stabilize at 0 Hz.
Note: DO NOT tap on plastic engine components.
Showing posts with label P0326. Show all posts
Showing posts with label P0326. Show all posts
Wednesday, November 11, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2023
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2023
DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
Diagnostic Aids
* Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set.
* Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set.
* The KS mounting surface should be free of burrs, casting flash, and foreign material.
* The KS must be clear of hoses, brackets, and engine electrical wiring.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
J 35616 GM Approved Terminal Test Kit
Circuit/System Verification
1. Engine at operating temperature, observe DTC information with a scan tool. DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or
P0333 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
P0324
Note: If DTC P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are also set, diagnose those DTCs first.
DTC P0324 indicates an internal control module circuitry failure. Replace the ECM.
P0325, P0326, P0327, P0328, P0330, P0332, P0333
1. Ignition OFF, disconnect the affected KS.
2. Ignition OFF. Connect a DMM to both KS signal circuits, terminals A and B, at the affected KS. Set the DMM to the 400 mV AC scale,
select the Hz mode. Let the reading stabilize at 0 Hz.
Note: DO NOT tap on plastic engine components.
3. Tap on the engine block with a non-metallic object near the affected KS and observe the DMM for a fluctuating frequency.
瀚慖f the DMM does not display a fluctuating frequency while tapping on the engine block then replace the affected KS.
4. Verify the affected KS is properly tightened, refer to Fastener Tightening Specifications (See: Engine, Cooling and
DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
Diagnostic Aids
* Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set.
* Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set.
* The KS mounting surface should be free of burrs, casting flash, and foreign material.
* The KS must be clear of hoses, brackets, and engine electrical wiring.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
J 35616 GM Approved Terminal Test Kit
Circuit/System Verification
1. Engine at operating temperature, observe DTC information with a scan tool. DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or
P0333 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
P0324
Note: If DTC P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are also set, diagnose those DTCs first.
DTC P0324 indicates an internal control module circuitry failure. Replace the ECM.
P0325, P0326, P0327, P0328, P0330, P0332, P0333
1. Ignition OFF, disconnect the affected KS.
2. Ignition OFF. Connect a DMM to both KS signal circuits, terminals A and B, at the affected KS. Set the DMM to the 400 mV AC scale,
select the Hz mode. Let the reading stabilize at 0 Hz.
Note: DO NOT tap on plastic engine components.
3. Tap on the engine block with a non-metallic object near the affected KS and observe the DMM for a fluctuating frequency.
瀚慖f the DMM does not display a fluctuating frequency while tapping on the engine block then replace the affected KS.
4. Verify the affected KS is properly tightened, refer to Fastener Tightening Specifications (See: Engine, Cooling and
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2013
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2013
* DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are not set.
* The engine speed is at least 400 RPM.
* The engine coolant temperature (ECT) is warmer than -40掳C (-40掳F).
* The engine run time is at least 2 s.
* The power take-off (PTO) is not active.
* DTCs P0325 and P0330 run continuously when the above conditions are met.
P0326
* DTC P0068, P0606, P1516, P2101, P2135, or P2176 are not set.
* The engine speed is at least 400 RPM.
* The MAP is at least 10 kPa.
* DTC P0324 runs continuously when the above conditions are met.
P0327, P0328, P0332, and P0333
* The engine coolant temperature (ECT) is warmer than -40掳C (-40掳F).
* The engine run time is at least 2 s.
* DTCs P0327, P0328, P0332, and P0333 run continuously when the above conditions are met.
Conditions for Setting the DTC
P0324
The ECM has detected an internal circuitry fault for 5 s.
P0325 and P0330
The KS signal circuits are open or shorted together for 5 s.
P0326
* The KS signal indicates an engine knock is present.
* The ECM has commanded the spark retard to a value, which is more than the calibrated value, for a specific engine load and speed.
* The above conditions exist for more than 5 s.
P0326
* The KS signal indicates an engine knock is present.
* The ECM has commanded the spark retard to a value, which is more than the calibrated value, for a specific engine load and speed.
* The above conditions exist for more than 5 s.
P0327, P0328, P0332, and P0333
* The KS signal circuits are shorted to voltage or ground.
* The above conditions exist for more than 5 s.
Action Taken When the DTC Sets
* DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
* The ignition timing is retarded to reduce the potential of engine damaging spark knock.
Conditions for Clearing the DTC
DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
Diagnostic Aids
* Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set.
* Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set.
* The KS mounting surface should be free of burrs, casting flash, and foreign material.
* The KS must be clear of hoses, brackets, and engine electrical wiring.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
* DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are not set.
* The engine speed is at least 400 RPM.
* The engine coolant temperature (ECT) is warmer than -40掳C (-40掳F).
* The engine run time is at least 2 s.
* The power take-off (PTO) is not active.
* DTCs P0325 and P0330 run continuously when the above conditions are met.
P0326
* DTC P0068, P0606, P1516, P2101, P2135, or P2176 are not set.
* The engine speed is at least 400 RPM.
* The MAP is at least 10 kPa.
* DTC P0324 runs continuously when the above conditions are met.
P0327, P0328, P0332, and P0333
* The engine coolant temperature (ECT) is warmer than -40掳C (-40掳F).
* The engine run time is at least 2 s.
* DTCs P0327, P0328, P0332, and P0333 run continuously when the above conditions are met.
Conditions for Setting the DTC
P0324
The ECM has detected an internal circuitry fault for 5 s.
P0325 and P0330
The KS signal circuits are open or shorted together for 5 s.
P0326
* The KS signal indicates an engine knock is present.
* The ECM has commanded the spark retard to a value, which is more than the calibrated value, for a specific engine load and speed.
* The above conditions exist for more than 5 s.
P0326
* The KS signal indicates an engine knock is present.
* The ECM has commanded the spark retard to a value, which is more than the calibrated value, for a specific engine load and speed.
* The above conditions exist for more than 5 s.
P0327, P0328, P0332, and P0333
* The KS signal circuits are shorted to voltage or ground.
* The above conditions exist for more than 5 s.
Action Taken When the DTC Sets
* DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
* The ignition timing is retarded to reduce the potential of engine damaging spark knock.
Conditions for Clearing the DTC
DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0332, and P0333 are Type B codes.
Diagnostic Aids
* Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set.
* Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set.
* The KS mounting surface should be free of burrs, casting flash, and foreign material.
* The KS must be clear of hoses, brackets, and engine electrical wiring.
Reference Information
Schematic Reference
Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic
Ignition System Description)
Electrical Information Reference
Tuesday, November 10, 2020
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2009
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2009
P0326
DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0324
- Knock Sensor (KS) Module Performance
DTC P0325
- Knock Sensor (KS) Circuit Bank 1
DTC P0326
- Knock Sensor (KS) Performance
DTC P0327
- Knock Sensor (KS) Circuit Low Voltage Bank 1
DTC P0328
- Knock Sensor (KS) Circuit High Voltage Bank 1
DTC P0330
- Knock Sensor (KS) Circuit Bank 2
DTC P0332
- Knock Sensor (KS) Circuit Low Voltage Bank 2
DTC P0333
- Knock Sensor (KS) Circuit High Voltage Bank 2
Diagnostic Fault Information
Circuit/System Description
The knock sensor (KS) system enables the engine control module (ECM) to control the ignition timing for the best possible performance while
protecting the engine from potentially damaging levels of detonation. The ECM monitors 2 separate KS, one on each side of the engine block. Each
KS produces an AC voltage that varies, depending on the vibration levels detected during engine operation. The ECM receives the KS signal
through 2 isolated signal circuits for each KS. The ECM adjusts the spark timing based on the amplitude and frequency of each KS signal. The
ECM learns a minimum noise level for each sensor at idle speeds, and uses calibrated noise level values for the rest of the RPM range. The ECM
should monitor a normal KS signal within the noise channel.
Conditions for Running the DTC
P0324
* DTC P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are not set.
* The engine speed is at least 400 RPM.
* DTC P0324 runs continuously when the above conditions are met.
P0325 or P0330
* DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are not set.
* The engine speed is at least 400 RPM.
* The engine coolant temperature (ECT) is warmer than -40掳C (-40掳F).
* The engine run time is at least 2 s.
* The power take-off (PTO) is not active.
P0326
DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0324
- Knock Sensor (KS) Module Performance
DTC P0325
- Knock Sensor (KS) Circuit Bank 1
DTC P0326
- Knock Sensor (KS) Performance
DTC P0327
- Knock Sensor (KS) Circuit Low Voltage Bank 1
DTC P0328
- Knock Sensor (KS) Circuit High Voltage Bank 1
DTC P0330
- Knock Sensor (KS) Circuit Bank 2
DTC P0332
- Knock Sensor (KS) Circuit Low Voltage Bank 2
DTC P0333
- Knock Sensor (KS) Circuit High Voltage Bank 2
Diagnostic Fault Information
Circuit/System Description
The knock sensor (KS) system enables the engine control module (ECM) to control the ignition timing for the best possible performance while
protecting the engine from potentially damaging levels of detonation. The ECM monitors 2 separate KS, one on each side of the engine block. Each
KS produces an AC voltage that varies, depending on the vibration levels detected during engine operation. The ECM receives the KS signal
through 2 isolated signal circuits for each KS. The ECM adjusts the spark timing based on the amplitude and frequency of each KS signal. The
ECM learns a minimum noise level for each sensor at idle speeds, and uses calibrated noise level values for the rest of the RPM range. The ECM
should monitor a normal KS signal within the noise channel.
Conditions for Running the DTC
P0324
* DTC P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are not set.
* The engine speed is at least 400 RPM.
* DTC P0324 runs continuously when the above conditions are met.
P0325 or P0330
* DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333 are not set.
* The engine speed is at least 400 RPM.
* The engine coolant temperature (ECT) is warmer than -40掳C (-40掳F).
* The engine run time is at least 2 s.
* The power take-off (PTO) is not active.
Subscribe to:
Posts (Atom)