2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Technical Service Bulletin # 11-06-04-007C Date: 121109
Engine Controls - MIL ON, DTC P2135, Reduced Engine Power
TECHNICAL
Bulletin No.: 11-06-04-007C
Date: November 08, 2012
Subject: Diagnosis and Repair - Malfunction Indicator Lamp (MIL) Illuminated, Reduced Engine Power Message Displayed, DTC P2135 Set
Models:
2008-2011 Cadillac Escalade Models
2009-2011 Cadillac Escalade Two-Mode Hybrid
2008-2009 Chevrolet TrailBlazer
2008-2011 Chevrolet Avalanche, Colorado, Express, Silverado, Suburban, Tahoe
2008-2011 Chevrolet Tahoe Two-Mode Hybrid
2009-2011 Chevrolet Silverado Two-Mode Hybrid
2008-2009 GMC Envoy
2008-2011 GMC Canyon, Savana, Sierra, Sierra Denali, Yukon Models
2008-2011 GMC Yukon Two-Mode Hybrid
2009-2011 GMC Sierra Two-Mode Hybrid
2008-2009 HUMMER H2
2008-2010 HUMMER H3
Equipped with Engine RPO LFA, LY2, L20, LMG, LC9, LH6, LMF, LH8, LH9, L76, LS2, LY5, LY6, L92, L96, LZ1, L94 or L9H
Attention:
If a vehicle is encountered with this condition, DO NOT replace the throttle body. Instead follow this procedure below. ALL Model Year
2008-2011 vehicles MUST have the engine control module (ECM) reprogrammed with the latest software calibration as indicated in Step 35 of the
procedure AFTER the installation of the throttle position (TP) sensor cover. ALL 2011 Model Year vehicles will receive the enhanced oil life
monitor (OLM) algorithm as part of the new ECM calibration. The enhanced OLM algorithm will provide a maximum mileage of 7,500 miles
(12,000 km) between oil changes.
Supercede:
This bulletin is being revised to add 2011 Model Year vehicles to the reprogramming statement in the Attention and to identify that the 2011 ECM
calibration includes the enhanced oil life monitor (OLM) algorithm that has a maximum of 7,500 miles (12,000 km) between oil changes. Please
discard Corporate Bulletin Number 11-06-04-007B (Section 06 - Engine/Propulsion System).
Condition
Some customers may comment on an illuminated malfunction indicator lamp (MIL), with a Reduced Engine Power message displayed.
The technician may observe on a scan tool DTC P2135: Throttle Position (TP) Sensor 1-2 Correlation set as Current or in History.
Cause
This condition may be caused by the difference between the TP Sensor 1 and TP Sensor 2 exceeding a calibrated value for more than 2 seconds.
Correction
Caution
Handle the electronic throttle control components carefully. Use cleanliness in order to prevent damage. Do not drop the electronic throttle
control components. Do not roughly handle the electronic throttle control components. Do not immerse the electronic throttle control
components in cleaning solvents of any type.
Warning
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 6
Approved safety glasses and gloves should be worn when performing this procedure to reduce the chance of personal injury.
1. With a scan tool, verify that DTC P2135 is set as Current or in History.
瀚慖f DTC P2135 is set as Current or in History, proceed to Step 2.
瀚慖f DTC P2135 is not set as Current or in History, refer to Diagnostic Trouble Code (DTC) List - Vehicle or Symptoms - Engine Controls
in SI.
2. Turn OFF the ignition.
3. Open the hood.
Important
If at any time during this procedure the throttle body is dropped, abort this procedure and REPLACE it with a new throttle body
assembly.
4. Remove the throttle body and discard the throttle body gasket. Refer to Throttle Body Assembly Replacement in SI.
5. Remove any loose debris and dirt from the throttle body assembly and the TP sensor cover. Inspect the throttle body for damage.
Caution
Do not use any solvent that contains Methyl Ethyl Ketone (MEK). This solvent may damage fuel system components.
6. Clean the throttle body bore and the throttle plate using a clean shop towel with GM Top Engine Cleaner, P/N 1052626 (in Canada, P/N
993026), or ACDelco Upper Engine and Fuel Injector Cleaner, P/N 88861803, or an equivalent product.
Notice
DO NOT mount the throttle body in a vise. The throttle body can be set on the top of a soft protected workbench area.
7. Hold the throttle body with your hand, so that the throttle position (TP) sensor cover is facing upward as shown.
8. Secure a rubber band around the throttle body and TP sensor cover as shown.
9. Turn over the throttle body and use a flathead screwdriver to remove the two clips (1, 2) as shown. Discard the clips.
Notice
DO NOT PRY ON THE MACHINED SEALING SURFACE OF THE THROTTLE BODY INLET DUCT.
10. Turn over the throttle body and use a flathead screwdriver to remove the four remaining clips from the TP sensor cover. Discard the clips.
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 7
11. Hold the throttle body with your hand, so that the TP sensor cover is facing upward. Grasp the TP sensor cover and carefully lift it up and
separate it from the throttle body.
Notice
DO NOT allow the intermediate gear to fall out.
12. Maintain the throttle body in an upward position. Use your thumb to maintain contact with the intermediate gear. => If the intermediate gear
falls out and impacts a hard workbench surface or the floor, abort this procedure and REPLACE with a new throttle body assembly.
13. Verify that the TP sensor cover gasket HAS REMAINED in the TP sensor cover as shown. Ensure that the gasket is accounted for and
remains with the old TP sensor cover.
14. Observe the TP sensor cover for missing female throttle actuator motor terminals (1). Verify that the female throttle actuator motor terminals
HAVE REMAINED in the TP sensor cover and HAVE NOT been retained on the throttle actuator motor male terminals (2). Discard the old
TP sensor cover, gasket and terminals.
瀚?If one or both of the TP sensor cover female throttle actuator motor terminals HAVE BEEN retained on the throttle actuator motor male
terminals (2), remove and discard those female terminals.
15. Remove the new TP sensor cover from the protective shipping wrapper.
16. Place the TP sensor cover in the position as shown. Confirm the TP sensor drive slot orientation is aligned in the TP sensor cover as shown.
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 8
瀚慖f the TP sensor drive slot orientation is not aligned as shown, use a small flathead screwdriver to gently rotate the TP sensor drive slot
clockwise to the wide open throttle (WOT) position as shown.
17. Verify that the TP sensor cover gasket is secure and properly positioned.
Notice
The three TP sensor cover alignment tabs are highlighted in white for identification purposes only.
18. Verify that all three of the TP sensor cover alignment tabs are present and are not damaged.
19. Grasp and hold the throttle body in the previously hand held upward position. Lightly depress the intermediate gear to verify that it is fully
seated and the gears are engaged.
20. Rotate the throttle body plate to the WOT position (1).
21. Position and install the TP sensor cover to the throttle body. Hold the TP sensor cover in position. If necessary for ease of the clip
installation, secure a rubber band around the throttle body and TP sensor cover.
22. Install the first TP sensor cover clip (1) in the position shown.
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 9
23. Install the remaining TP sensor cover clips in the sequence shown.
24. Install a NEW throttle body gasket to the intake manifold.
25. Install the throttle body, bolts and nuts. DO NOT tighten the fasteners yet.
26. Connect the electrical connector to the throttle body.
27. Turn ON the ignition. Clear the DTC with a scan tool.
28. Observe the scan tool TP Sensor 1 and 2 Agree/Disagree parameter while slowly depressing the accelerator pedal to WOT and then slowly
returning the pedal to closed throttle. Repeat the procedure several times. Rapidly depress the accelerator pedal from the rest position to the
wide open throttle position (WOT) and release pedal. Repeat the procedure several times. The TP Sensor 1 and 2 Agree/Disagree parameter
should display Agree.
瀚慖f TP Sensor 1 and 2 Agree/Disagree parameter displays Agree, proceed to Step 29.
瀚慖f TP Sensor 1 and 2 Agree/Disagree parameter displays Disagree, replace the throttle body assembly.
29. Observe the ECM module DTC information. Are DTC P1516, P2101 and/or P2176 set?
瀚慖f DTC P1516, P2101 and/or P2176 are set, replace the throttle body.
瀚?If DTC P1516, P2101 and/or P2176 are not set, proceed to Step 30.
30. Tighten the throttle body fasteners.
Tighten
Tighten the fasteners to 10 Nm (89 lb in).
31. Install any remaining components that were removed during this procedure.
32. Verify the battery voltage is more than 12 volts but less than 16 volts before proceeding with ECM reprogramming.
33. During reprogramming, the battery voltage must be maintained within the proper range of 12-15 volts. Connect the approved Midtronics(R)
PSC 550 Battery Maintainer (SPS Programming Support Tool EL-49642) to the vehicle.
瀚慖f the above recommended tool is not available, DO NOT connect a battery charger to the vehicle. Connect a fully charged 12V jumper or
booster pack that is disconnected from the AC voltage supply.
34. Use a Tech 2(R) or a multiple diagnostic interface (MDI) module for reprogramming. Ensure that either device is updated with the latest
available software version before performing the reprogramming event.
Notice
Customers that own 2011 Model Year vehicles should be advised of the enhanced OLM algorithm that has a maximum of 7,500 miles
(12,000 km) between oil changes.
35. Reprogram the ECM using the Service Programming System (SPS) with the latest calibration available on TIS2WEB. Refer to the SPS
procedures in SI.
36. Perform the Throttle Learn Reset Procedure. Refer to Throttle/Idle Learn > Throttle Learn > Reset Procedure in SI.
MIDTRONICS is a registered trademark of MIDTRONICS, INC.
Tech 2 is a registered trademark of General Motors LLC
ACDELCO is a registered trademark of General Motors LLC
Part Information
Important
The initial inventory for P/N 19259452 (Sensor Kit) will be distributed via RIM through a special stocking policy. The dealership parts
department personnel will need to approve the stocking policy in order to receive the initial shipment. Subsequent replenishment will also
2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 10
be via RIM. If the parts department is out of inventory of P/N 19259452 (Sensor Kit), then to complete the repair utilize the throttle body
assembly.
Warranty Information
- For 2008-2009 vehicles repaired under the 5 year/100,000 mile (160,000 km) Powertrain Coverage (Code P) warranty, use:
- For 2010-2011 Cadillac vehicles repaired under the 4 year/50,000 mile (80,000 km) Bumper-to-Bumper warranty (in Canada, Base Warranty
Coverage), use:
- For 2010-2011 Chevrolet, GMC or HUMMER vehicles repaired under the 3 year/36,000 mile (60,000 km) Bumper-to-Bumper warranty (in
Canada, Base Warranty Coverage), use:
- For 2010-2011 Chevrolet, GMC or HUMMER vehicles repaired under the 3 year/50,000 mile (80,000 km) California Emission Coverage
(Code E) warranty, use:
