2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 1008
Reference Information
Schematic Reference
Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics
(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine idling at operating temperature for at least 30 s. Observe the DTC information, DTCs P0030, P0031, P0032, P0036, P0037, and
P0038 should not set.
2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the appropriate B52 Heated Oxygen Sensor.
2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.
Note: The ignition circuit supplies voltage to other components. Make sure you test all circuits for a short to ground or test all components
for being shorted that share the ignition circuit.
瀚慖f the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and
the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.
3. Connect a test lamp between the heater control circuit terminal 2 and B+. The test lamp should not illuminate.
瀚慖f the test lamp is always ON, test the control circuit for a short to ground. If the circuit/connections test normal, replace the K20 Engine
Control Module.
Note: The control circuit for the HO2S heater is pulled-up to voltage within the ECM, 2.0-3.0 V on the control circuit is normal.
4. Idle the engine, and verify the test lamp illuminates or flashes.
瀚慖f the test lamp is always OFF, test the control circuit terminal 2 for an open/high resistance. If the circuit/connections test normal, replace
the K20 Engine Control Module.
5. Ignition ON, test for 2.0-3.0 V between the control circuit terminal 2 and ground.
瀚慖f not within the specified range, test the control circuit for a short to voltage. If the circuit/connections test normal, replace the K20
Engine Control Module.
6. If all circuits/connections test normal, test or replace the B52 Heated Oxygen Sensor.
Component Testing
1. Ignition OFF, disconnect the harness connector at the B52 Heated Oxygen Sensor.
2. Test for 5-25 ohm between the control terminal 2 and the ignition terminal 1 of the B52 Heated Oxygen Sensor.
