2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2042

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 2042

瀚慖f another DTC is present, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) and perform the appropriate diagnostic.

4. To verify that the performance of the catalytic converter has not been affected by the condition that set this DTC, perform the Repair

Verification for DTC P0420 or P0430. Refer to DTC P0420 or P0430 (See: P Code Charts/P0420).

P0353

DTC P0351-P0358

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0351

- Ignition Coil 1 Control Circuit

DTC P0352

- Ignition Coil 2 Control Circuit

DTC P0353

- Ignition Coil 3 Control Circuit

DTC P0354

- Ignition Coil 4 Control Circuit

DTC P0355

- Ignition Coil 5 Control Circuit

DTC P0356

- Ignition Coil 6 Control Circuit

DTC P0357

- Ignition Coil 7 Control Circuit

DTC P0358

- Ignition Coil 8 Control Circuit

Diagnostic Fault Information

Circuit/System Description

The ignition system on this engine uses an individual coil/module for each cylinder. The engine control module (ECM) controls the spark event for

each cylinder through the eight individual ignition control (IC) circuits. When the ECM commands the IC circuit ON, electrical current will flow

through the primary winding of the ignition coil, creating a magnetic field. When a spark event is requested, the ECM will command the IC circuit

OFF, interrupting current flow through the primary winding. The magnetic field created by the primary winding will collapse across the secondary

coil windings, producing a high voltage across the spark plug electrodes. The ECM uses information from the crankshaft position (CKP) sensor,

and the camshaft position (CMP) sensor for sequencing and timing of the spark events. Each ignition coil/module assembly has the following

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1805

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1805

瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: All modules must be powered down or misdiagnosis may result.

1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.

2. Ignition OFF, all vehicle systems OFF, this may take up to 2 minutes, test for less than 5 ohm between the low reference circuit terminal A

and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition ON, verify the appropriate scan tool B52 HO2S parameter is approximately 450 mV.

瀚慖f less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the appropriate scan tool B52 HO2S

parameter is less than 60 mV.

瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

5. If all circuits test normal, replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain

Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for ECM replacement, setup, and programming

P0140

DTC P0134, P0140, P0154, or P0160

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0134

- HO2S Circuit Insufficient Activity Bank 1 Sensor 1

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 914

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 914

瀚慖f any listed DTC is present, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) to diagnose that DTC prior to this diagnostic.

2. Replace the K17 Electronic Brake Control Module (EBCM) and verify the DTC does not reset.

瀚慖f the DTC resets, replace the module that set the DTC.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for module replacement, setup and programming

P000A

DTC P000A-P000D, P0011, P0014, P0021, or P0024 (Without LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P000A

- Intake Camshaft Position System Slow Response Bank 1

DTC P000B

- Exhaust Camshaft Position System Slow Response Bank 1

DTC P000C

- Intake Camshaft Position System Slow Response Bank 2

DTC P000D

- Exhaust Camshaft Position System Slow Response Bank 2

DTC P0011

- Intake Camshaft Position System Performance Bank 1

DTC P0014

- Exhaust Camshaft Position System Performance Bank 1

DTC P0021

- Intake Camshaft Position System Performance Bank 2

DTC P0024

- Exhaust Camshaft Position System Performance Bank 2

Circuit/System Description

The camshaft position actuator system enables the Engine Control Module (ECM) to change the timing of the camshafts while the engine is

operating. The camshaft position actuator solenoid signal from the ECM is pulse width modulated (PWM). The ECM controls the camshaft position

actuator solenoid duty cycle by controlling the amount of solenoid ON time. The camshaft position actuator solenoid controls the advance or the

retard of each camshaft. The camshaft position actuator solenoid controls the oil flow that applies the pressure to advance or retard the camshafts.

Conditions for Running the DTC

* DTC P0010, P0013, P0016, P0017, P0018, P0019, P0020, P0023, P2088, P2089, P2090, P2091, P2092, P2093, P2094, and P2095 is not set.

* The engine speed is greater than 560 RPM.

* The engine is operating for greater than 1 s.

* The engine coolant temperature is between -48 to +143掳C (-54 to +289掳F).

* The engine oil temperature is less than -48掳C (-54掳F).

* The engine must accelerate such that the camshaft position actuator system is commanded from the park position to the phased position. This

is considered a cam control cycle. There must be a minimum of 2 cam control cycles for at least 2.5 s each in the phased position.

* DTCs P000A, P000B, P000C, P000D, P0011, P0014, P0021, and P0024 run continuously once the above conditions are met for greater than

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 951

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 951

瀚慖f any other DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine idling at operating temperature, observe the appropriate B52 HO2S parameter with a scan tool. Verify the following:

* The B52 HO2S 1 value should vary from below 200 mV to above 800 mV and respond to fueling changes.

* The B52 HO2S 2 value should change greater than 200 mV when the throttle is quickly cycled 3 times from closed to wide open and

back to closed after running the engine at 1,500 RPM for 30 s.

3. Engine idling, observe the scan tool HO2S 1 voltage parameter. The voltage should fluctuate above and below the range of 350-550 mV.

4. Observe the DTC information with a scan tool. DTCs P0133, P013A, and P013E should not set.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Verify that none of the following conditions exist:

* Lean or rich fuel injectors-Refer to Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Injector/Testing and Inspection/Fuel Injector Solenoid Coil Test)Fuel Injector Solenoid Coil Test (LF1, LFW) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection/Fuel Injector Solenoid Coil Test).

* Water intrusion in the HO2S harness connector

* HO2S wiring harness damage

* Incorrect RTV sealant

* Low or high fuel system pressure-Refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel

System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel

System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).

* Fuel that is contaminated-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool) (See: Powertrain Management/Fuel Delivery

and Air Induction/Fuel/Testing and Inspection/Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool))Alcohol/Contaminants-in-Fuel

Diagnosis (Without Special Tool) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component

Tests and General Diagnostics/Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)).

* Fuel saturation of the evaporative emission (EVAP) canister

* Exhaust leaks near the HO2S

* Engine vacuum leaks

* Engine oil consumption

* Engine coolant consumption

瀚慖f you find any of the above conditions, repair as necessary.

2. If all conditions test normal, replace the B52 HO2S.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Sensor 1 (LAU) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Sensor 1)

* Heated Oxygen Sensor Replacement - Sensor 2 (LAU) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Sensor 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for engine control module replacement, setup, and

programming

P0014

DTC P000A-P000D, P0011, P0014, P0021, or P0024 (Without LF1, LFW)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 916

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 916

瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle) for further diagnosis.

2. Engine idling, command the appropriate Camshaft Position Actuator from 0 degrees to 40 degrees and back to zero while observing the

appropriate scan tool Camshaft Position Variance parameters. The Camshaft Position Variance should be less than 2 degrees in each of the

commanded states.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Ignition ON, load test for B+ between the ignition circuit terminal 1 and ground.

瀚慖f less than the specified range, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal

and the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary.

Note: Use the J 35616-200 - Test Lamp Kit for this test. If the J 35616-200 - Test Lamp Kit is not available, use a test lamp that measures

greater than 20 ohm.

3. Connect a test lamp between the control circuit terminal 2 and B+.

Note: The voltage must be measured at the control side of the circuit.

4. Command the appropriate Camshaft Position Actuator Solenoid Valve ON with a scan tool. Load test for less than 1 V between the control

circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the control circuit for an open/high resistance. If the circuit/connections test normal, replace the

K20 Engine Control Module.

5. Remove the Camshaft Position Actuator Solenoid Valve. Inspect the Camshaft Position Actuator Solenoid Valve and mounting area for the

following conditions:

* For a torn, restricted, mis-positioned, or missing screens at the Camshaft Position Actuator Solenoid Valve

* For engine oil leaks between the oil sealing lands of the Camshaft Position Actuator Solenoid Valve. Inspect the lands of the Camshaft

Position Actuator Solenoid Valve for nicks

* For oil seepage at the Camshaft Position Actuator Solenoid Valve connector

瀚慖f a condition is found, replace Q6 Camshaft Position Actuator Solenoid Valve.

6. Ignition OFF, swap the appropriate Camshaft Position Actuator Solenoid Valve with a Camshaft Position Actuator Solenoid Valve that is

operating correctly.

7. Engine idling. Command the appropriate Camshaft Position Actuator from 0 degrees to 40 degrees and back to zero while observing the

appropriate scan tool Camshaft Position Variance parameters. The Camshaft Position Variance should be less than 2 degrees in each of the

commanded states.

瀚慖f greater than the specified value, replace the mechanical camshaft position actuator.

8. If all circuits/connections test normal, test or replace the Q6 Camshaft Position Actuator Solenoid Valve.

Component Testing

1. Ignition OFF, disconnect the harness connector at the appropriate Q6 Camshaft Position Actuator Solenoid Valve.

2. Test for 7-12 ohm between the control terminal 2 and the ignition terminal 1 of the Q6 Camshaft Position Actuator Solenoid Valve.

瀚慖f not within the specified range, replace the Q6 Camshaft Position Actuator Solenoid Valve.

3. Test for infinite resistance between each terminal and the Q6 Camshaft Position Actuator Solenoid Valve housing.

瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Replacement - Bank 1 (Right Side) Exhaust (LAU) (See: Engine, Cooling and Exhaust/Engine/Camshaft,

Lifters and Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake (LAU) (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters

and Push Rods/Camshaft/Service and Repair/Camshaft Position Actuator Replacement - Bank 1 (Right Side) Intake)