Sunday, December 1, 2019

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Technical Service Bulletin # 09-08-48-006 Date: 090918

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Technical Service Bulletin # 09-08-48-006 Date: 090918



Body - Stain/Film On Windshield Glass Perimeter



TECHNICAL



Bulletin No.: 09-08-48-006



Date: September 18, 2009



Subject: Clear Stain or Film on Inside Perimeter of Windshield Glass (Clean/Polish Glass)



Models:



2010 and Prior Passenger Cars and Trucks (Including Saturn and Saab)



2010 and Prior HUMMER H2, H3



Condition



Some customers may comment on a clear stain or film on the inside of the windshield glass. This condition appears along the outer edges of the



glass along the top, bottom or A-pillar areas. Normal glass cleaning procedures will not remove the stain.



Cause



The assembly plant uses a clear sealer/primer on the outer edge of the windshield glass to improve adhesion to the urethane adhesive that bonds the



windshield glass to the vehicle body. Excess sealer/primer may drip or flow onto the windshield and cause a stain. Once the sealer/primer dries, it



may appear to have etched the glass.



Correction



Note



A "white" type of toothpaste is recommended for this repair. Gel-type toothpaste may provide less satisfactory results.



Use a small amount of toothpaste on a soft, cotton cloth to polish the stained area. It may be necessary to wrap the cloth around a paint stir stick or a



similar tool to reach the lower corners of the windshield glass.



After polishing the glass, clean the inside of the windshield glass with a clean, damp, cotton cloth and verify all of the stain is removed. Do not use



any cleaners or solvents - use only clean warm water.



Warranty Information (excluding Saab U.S. Models)



For vehicles repaired under warranty, use:



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 249



Warranty Information (Saab U.S. Models)



For vehicles repaired under warranty, use the table.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 864

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 864



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information



Special Tools



J-46079 Tire Pressure Monitor Diagnostic Tool



Circuit/System Verification



1. Using the J-46079 , activate each tire pressure sensor and record each sensors transmission data and physical location. Verify J-46079



displays the 8-digit ID number, accurate tire pressure +/- 27.6 kPa (4 psi), Learn Mode, and at least a 1/4 graph signal strength displayed.



瀚慖f any of the parameters listed above are not displayed, replace the suspect tire pressure sensor.



2. With the scan tool, verify tire pressure sensors ID and locations displayed on the scan tool match the IDs and locations recorded from the



special tool.



瀚慖f the IDs and locations do not match, perform the Tire Pressure Indicator Sensor Learn (See: Instrument Panel, Gauges and Warning



Indicators/Tire Monitoring System/Tire Pressure Sensor/Testing and Inspection).



3. Enable the TPM learn mode. Use the J-46079 in simulate mode to learn 4 simulated sensor transmissions into the BCM. Verify that all 4



simulated sensor locations, IDs, and tire pressures displayed on the TPM special tool match the corresponding scan tool parameters



displayed.



瀚慖f the scan tool does not match, replace the K9 BCM.



4. Test drive the vehicle above 40 km/h (25 mph) for greater than 2 minutes. With the scan tool, observe the suspect Pressure Sensor Mode data



parameter. Verify the sensor mode changes to Rolling.



瀚慖f the Pressure Sensor Mode does not change, replace the suspect tire pressure sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Tire Pressure Indicator Sensor Replacement (See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure



Sensor/Service and Repair)



* Tire Pressure Indicator Sensor Learn (See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure



Sensor/Testing and Inspection)



* Control Module References (See: Testing and Inspection/Programming and Relearning)for BCM replacement, setup and programming.



C0755



DTC C0750, C0755, C0760, or C0765



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions)provides an overview of each diagnostic category.



DTC Descriptor



DTC C0750 03



- Left Front Tire Pressure Sensor Low Voltage



DTC C0750 29



- Left Front Tire Pressure Sensor Too Few Pulses



DTC C0750 39



- Left Front Tire Pressure Sensor Internal Malfunction



DTC C0755 03



- Right Front Tire Pressure Sensor Low Voltage

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 625

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 625



Circuit/System Verification



Verify DTC B3122, B3123, or B3124 is not set.



If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic



Trouble Code (DTC) List - Vehicle).



Circuit/System Testing



Note: The A24P passenger exterior door handle assembly has two harness connectors. Of these two harness connectors, make sure that only



the T10N passenger door handle keyless entry antenna harness connector is disconnected. Disconnecting both harness connectors will result



in the inability to activate the antenna and cause an improper diagnosis.



1. Ignition OFF, disconnect the harness connector at the T10N passenger door handle keyless entry antenna.



2. Ignition ON, test for less than 1 V between the signal circuit terminal 1 and ground.



瀚慖f greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K84 keyless entry



control module.



3. Ignition OFF, install a DMM between the signal circuit terminal 1 and ground. Set the DMM to capture DC voltage using the MIN MAX



function.



4. Lock the vehicle doors using the keyless entry transmitter.



5. Activate the antenna by pulling the passenger exterior door handle. Verify the MAX voltage captured by the DMM is greater than.5 V.



瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace



the K84 keyless entry control module.



6. Install a DMM between the signal circuit terminal 1 and the low reference circuit terminal 2. Set the DMM to capture DC voltage using the



MIN MAX function.



7. Lock the vehicle doors using the keyless entry transmitter.



8. Activate the antenna by pulling the passenger exterior door handle. Verify the MAX voltage captured by the DMM is greater than.5 V.



瀚慖f less than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K84



keyless entry control module.



Note: Install the A24P passenger exterior door handle assembly and verify correct system operation BEFORE painting the assembly. If the



assembly does not correct the concern, return the unpainted part.



9. If all circuits test normal, replace the A24P passenger exterior door handle assembly. Verify DTC B3120 is not set.



瀚慖f the DTC is set, replace the K84 keyless entry control module.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Front Side Door Outside Handle Replacement (See: Body and Frame/Doors, Hood and Trunk/Doors/Front Door/Front Door Handle/Front



Door Exterior Handle/Service and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning)for keyless entry control module replacement, setup,



and programming



B3121



DTC B3121



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions)provides an overview of each diagnostic category.



DTC Descriptors



DTC B3121 02



- Keyless Entry Antenna 3 Short to Ground

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 743

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 743



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC B3948 02



- Left Front Turn Signal Circuit Short to Ground



DTC B3949 02



- Right Front Turn Signal Circuit Short to Ground



Diagnostic Fault Information



Circuit/System Description



Ground is applied at all times to the turn signal/multifunction switch. The turn signal lamps may only be activated with the ignition switch in the



ON or START position. When the turn signal/multifunction switch is placed in either the TURN RIGHT or TURN LEFT position, ground is



applied to the body control module through either the right turn or left turn signal switch signal circuit. The BCM then applies a pulsating voltage to



the front and rear turn signal lamps through there respective voltage supply circuits. When a turn signal request is received by the BCM, a serial



data message is sent to the instrument cluster requesting the respective turn signal indicator be pulsed ON and OFF.



Conditions for Running the DTC



When the appropriate turn signal is commanded



Conditions for Setting the DTC



B3948 02



The BCM detects a short to ground on the left front turn signal control circuit.



B3949 02



The BCM detects a short to ground on the right front turn signal control circuit.



Action Taken When the DTC Sets



The appropriate turn signal lamp is inoperative.



Conditions for Clearing the DTC



* The DTC will be current for as long as the fault is present.



* When the fault is no longer present, the DTC will be a history DTC.



* A history DTC will clear after 50 ignition cycles.



Reference Information



Schematic Reference



Exterior Lights Schematics (See: Diagrams/Electrical Diagrams/Lighting and Horns/System Diagram/Exterior Lights Schematics)



Connector End View Reference

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 212

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 212



Circuit/System Description



The digital radio receiver, located inside the radio, receives digital radio information from the digital radio antenna located on the outside of the



vehicle. The digital radio receiver is connected to the digital radio antenna via a shielded coax cable.



Conditions for Running the DTC



This DTC is run every 300 milliseconds.



Conditions for Setting the DTC



The radio detects a circuit fault in the digital radio antenna.



Action Taken When the DTC Sets



The radio displays No XM Signal or Check Antenna.



Conditions for Clearing the DTC



* A current DTC clears when the condition for setting the DTC is no longer present.



* A history DTC clears after 100 malfunction-free ignition cycles.



Reference Information



Schematic Reference



Radio/Navigation System Schematics (See: Accessories and Optional Equipment/Diagrams/Electrical Diagrams/Radio/Navigation System



Schematics)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



Radio/Audio System Description and Operation (See: Accessories and Optional Equipment/Description and Operation/Radio/Audio System)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic



Procedures/Connector Repairs/Connector Repairs)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



Special Tools



EL-48028 Digital Radio Test Antenna



Circuit System Verification



With the vehicle outside in an area with an unobstructed view of the southern sky, tune to XM. Verify XM reception is clear and the No XM Signal



message is not displayed on the radio.



Circuit/System Testing



1. Ignition OFF, disconnect the digital radio antenna coax cable from the radio. Connect the EL-48028 to the radio and place on the roof of the



vehicle.



2. Ignition ON, radio tuned to XM channel 1. Verify DTC B125C is not set as current and XM reception is improved.



瀚慖f DTC B125C is set as current or the reception is not improved, replace the radio.



3. Ignition OFF, reconnect the antenna coax cable at the radio. Disconnect the antenna coax cable from the digital radio antenna.



4. Ignition ON, radio ON, test for 4.5-5.5 V between the antenna coax cable center terminal and an outer shield.



瀚慖f less than the specified range, test the antenna coax cable for an open/high resistance.



瀚慖f greater than the specified range, test the antenna coax cable for a short to voltage.



5. If all circuits test normal, replace the digital radio antenna.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 422

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 422



9. Command the body control module-keyless entry control module-accessory power mode indicator test with a scan tool. The test lamp should



turn ON and OFF when changing between the commanded states.



瀚慖f the test lamp is always ON, test the control circuit for a short to voltage. If all circuits test normal, replace the K9 BCM.



瀚慖f the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If all circuits test normal, replace



the K9 BCM.



10. If all circuits test normal, replace the S38 ignition mode switch.



Component Testing



1. Ignition OFF, disconnect the harness at the S38 ignition mode switch.



2. Place a jumper wire between ignition mode switch terminal 4 and ground.



3. Place a fused jumper wire between the circuit terminals of the ignition mode switch listed below and B+:



* Ignition mode switch terminal 2



* Ignition mode switch terminal 5



瀚慖f the either LED does not light, replace the S38 ignition mode switch.



4. Without the button pressed, test for 4,870 ohm between the ignition mode switch terminals listed below:



* Ignition mode switch terminals 3 and 7



* Ignition mode switch terminals 4 and 6



瀚慖f not the specified value, replace the S38 ignition mode switch.



5. With the button pressed, test for 1,300 ohm between the ignition mode switch terminals listed below:



* Ignition mode switch terminals 3 and 7



* Ignition mode switch terminals 4 and 6



瀚慖f not the specified value, replace the S38 ignition mode switch.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Ignition and Start Switch Replacement (See: Powertrain Management/Ignition System/Sensors and Switches - Ignition System/Ignition



Switch/Service and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, programming and setup



B1000



DTC B1000



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC B1000 XX



- Electronic Control Unit



Circuit/System Description



The internal fault detection is handled inside the control module. The symptom byte listed in the DTC Descriptor is for engineering reference only.



No external circuit diagnosis is involved.



Conditions for Running the DTC



The module runs the program to detect an internal fault when power up is commanded. The only requirements are voltage and ground. This



program runs even if the voltage is out of the valid operating range.

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Technical Service Bulletin # 13-08-116-001A Date: 130322

2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Technical Service Bulletin # 13-08-116-001A Date: 130322



Electrical - Aftermarket Interface Devices Causing Issues



TECHNICAL



Bulletin No.: 13-08-116-001A



Date: March 22, 2013



Subject: Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues



Models:



2006-2014 GM Passenger Cars and Trucks



Supercede:



This bulletin is being revised to add additional possible symptoms, clarify the language and revise the photos. Please discard Corporate Bulletin



Number 13-08-116-001 (Section 08 - Body and Accessories).



Condition



Customers may comment on various issues with their vehicle related to high or low speed data bus traffic. These concerns may be widely varied,



but some of the known issues are listed below.



The information contained in this bulletin is not meant to single out any one device or symptom, but to provide additional information that may be



useful for diagnosing issues that do not have other diagnostic methods to identify the root cause.



Note



This bulletin is being written with a focus on full size truck and full size van along with other fleet vehicles, but could apply to any vehicle.



Known Symptoms (not specific to any one device)



- The radio may not shut off after shutting down vehicle.



- Bus or LAN traffic may stay active leading to a discharged vehicle battery.



- Problems reprogramming modules either because of interference or the device will not allow the bus to power down.



- ONSTAR(R) may lose the ability to provide diagnostic data.



- Various engine and transmission performance issues with SES light set.



- Intermittent driveability issues.



- Reduced power message and codes.



- Stabilitrak(R) message and codes.



- C0561 stored in the EBCM leading to a traction control issue.



- No high speed LAN communication along with various communication U-codes.



- Transmission may not shift for one key cycle (TCM in default mode).



- Erratic gauge readings or flickering displays.



- SES, MIL or CEL light set and numerous DTC communication codes such as U0100, U0101, U186B and U1862.



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 385



- Diesel power-up devices causing no power in 4WD low range.



- Erratic electric power steering boost potentially associated with codes U2109, U2107, U2100, B1325, C0000.



- Service Tire Pressure Monitoring (TPM) system light illuminated.



-Cannot relearn TPM



- Specific to Hybrids:



- Reduced propulsion power message.



- Service high voltage charging system message.



Cause



If nothing else can be identified as the root cause of the issue after normal diagnostics as found in SI, check for a device plugged into the Assembly



Line Diagnostic Link (ALDL) or Data Link Connector (DLC) for tracking and/or maintenance interval scheduling. Monitoring devices, along with



other electronic accessories such as aftermarket cruise control, or police speed checking devices (RADAR or LIDAR) may cause one or more of the



concerns listed above.



Many of the problems described could be caused by an open connection on the HSCAN bus. Example: if the device only makes connection with



one CAN +, then it will cause bus errors and erratic ECU behavior.



These devices may be removed by the customer for use in another vehicle while theirs is brought in for service. The intent of this bulletin is to



identify a potential source of concerns that do not have other diagnostic methods to identify them. The examples below illustrate some of the



devices encountered.



Examples:



The monitoring device examples are not specific to any one design, and styles will vary.



Device W/Secondary DLC Connector



This device has another DLC connector on it. The rest of the harness along with the device can be placed out of sight hidden from the technician,



who may not notice the diagnostic connector is not in the factory location.



Pedal Mounted Aftermarket Device Interface



Aftermarket Device at ALDL



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 386



Aftermarket Device Switch



Monitoring Device Example



Fleet Tracking Device Interface (May Include Rental and Lease Vehicles)



Fleet Tracking Module Plugged Into the DLC



2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 387



Correction



If SI diagnostics do not identify the source of the issue and if the device is available, attempt to duplicate the condition, and then remove the device



to determine if the condition is eliminated.



If the customer's concern is resolved by removing the DLC interface device, inform the customer of the results, and that they should work with the



supplier of the device for further resolution.



If the condition is not eliminated with the device removed, continue diagnosing the vehicle with the appropriate Service Information.



Parts Information



There should not be any parts required. If on the rare occasion parts appear to have been damaged by the device or the installation of the device,



this would not be a defect covered under the New Vehicle Limited Warranty. For more information on Non-General Motors Parts & Equipment and



Original Equipment Alterations, please refer to Article 1.2.2.12 of the Service Policies & Procedures Manual. The repair order must be documented



correctly stating factual information on what alteration or product was identified on the vehicle.



Warranty Information



If ALDL interface devices are suspected as the root cause for a customer's concerns, submit a claim using the Z1111 labor operation to document



the concern as detailed in the latest version of Corporate Bulletin Number 09-00-89-016 "Warranty Administration - Labor Operation Z1111 -



Suspected Tampering or Vehicle Modifications, including submitting the claim under the appropriate labor operation and Customer Satisfaction



selection in Global Warranty Management.



If a claim is submitted to GM, follow all existing guidelines within the Service Policies & Procedures and GWM User Manual, Administrative



Messages, Bulletins or any other communication format.