2010 Cadillac Truck Escalade/ESV RWD V8-6.2L Page 1836
3. Ignition ON, verify the appropriate scan tool B52 HO2S parameter is approximately 450 mV.
瀚慖f less than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.
瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.
4. Ignition ON, install a 3 A fused jumper wire between the signal circuit terminal B and ground. Verify the appropriate scan tool B52 HO2S
parameter is less than 60 mV.
瀚慖f greater than the specified range, test the signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.
5. If all circuits test normal, replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
P0161
DTC P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141, P0155, or P0161
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P0030
- HO2S Heater Control Circuit Bank 1 Sensor 1
DTC P0036
- HO2S Heater Control Circuit Bank 1 Sensor 2
DTC P0050
- HO2S Heater Control Circuit Bank 2 Sensor 1
DTC P0053
- HO2S Heater Resistance Bank 1 Sensor 1
DTC P0054
- HO2S Heater Resistance Bank 1 Sensor 2
DTC P0056
- HO2S Heater Control Circuit Bank 2 Sensor 2
DTC P0059
- HO2S Heater Resistance Bank 2 Sensor 1
